Brick Brief: Flashing Chimneys

Flashing is an important element in brick masonry's line of defense against water penetration. Flashing may either direct moisture out of a cavity or prevent moisture from entering. Without flashing, any intersection or interruption of materials becomes an avenue for moisture to enter the construction. Several specific areas of potential moisture penetration must be addressed in the flashing of chimneys. This Brick Brief addresses these areas of concern and provides details for optimum performance. The Brick Brief "Proper Chimney Crowns" may also be of interest.

Chimney Construction
The use of flashing in chimneys presents some unique construction details. The three primary areas of concern are: the base of the chimney, the intersection of the chimney with the roof and the chimney crown.

The Base
The base of the chimney is constructed in much the same manner as a brick cavity wall. Flashing must be used at the joint between the foundation and the brickwork. The flashing should extend through the brick wythe and turn up behind the exterior face of the brick, ending in a mortar joint in the interior wythe. Weeps are placed immediately above the flashing.

Intersection with the Roof
The chimney penetration of the roof must be properly flashed to prevent water from entering the interior of the structure. Base and counter flashing must be installed at the interface. Base flashing is placed first, starting with the lower ends of the faces of the chimney perpendicular to the ridgeline, with tabs at each corner. The base flashing should extend a minimum of four inches (102 mm) along the roof and four inches (102 mm) up the chimney face as shown in Figure 1. Counter flashing is then lapped over the base flashing a minimum of three inches (76 mm), extended through the chimney wall, and turned up at an angle into the air space to collect water draining down the back of the brickwork as shown in Figure 2. All joints and laps in the base and counter flashing must be completely sealed. Weeps are not typically included.

/Public/News/20070412084400-1.jpg" width="416" height="310" border="0" alt="Figure 1">
Figure 1

/Public/News/20070412084400-2.jpg" width="416" height="310" border="0" alt="Figure 2">
Figure 2

The Chimney Crown
The area around the chimney crown is often overlooked as a source of moisture penetration. Flashing and sealant are important here to prevent water from entering the space between the chimney wall and the flue liner. The first piece of flashing should be placed directly below the chimney crown, extend through the brick wythe, and turn up against the outer face of the flue liner. This flashing should form a drip above the outside chimney face. A second piece of flashing should be folded over the top of the flue liner and extended down the outside to lap the first piece of flashing, as shown in Figure 3. For further information on chimney crown flashing, refer to Brick Brief "Proper Chimney Crowns."

/Public/News/20070412084400-3.jpg" width="416" height="310" border="0" alt="Figure 3">
Figure 3

Flashing Materials
The use of quality flashing materials cannot be overemphasized. The initial cost is money well spent to avoid costly future repairs. For flashing chimneys, metal flashings are recommended because of their resistance to high temperatures and exterior exposure. The Brick Brief "Through Wall Flashing" provides more detailed information on flashing materials.

Copper
Copper is durable, able to withstand elevated temperatures in the chimney, available in special performed shapes, and is an excellent moisture barrier. Copper can be safely embedded in fresh mortar and will not deteriorate in continuously saturated, hardened mortar unless excessive chlorides are present. Copper flashing may stain the concrete crown or brick masonry.

Stainless Steel
Stainless steel is an excellent flashing material. It provides a good water barrier, high-temperature resistance, and has excellent chemical resistance. ASTM A 240, Type 304 should be specified. The minimum thickness used should be 0.01 inch (0.25 mm).

Galvanized Steel
The life of galvanized steel flashing depends on the thickness of the zinc coating. However, thicker coatings may crack when folding the flashing. Galvanized steel is not recommended.

Aluminum
The alkalis present in fresh mortar will attack aluminum. Thus, aluminum should not be used as a flashing material in brick masonry.

Flashing Details and Installation
While flashing is essential to good performance of brick masonry, proper detailing and construction is of the utmost importance. Flashing that stops short of extending through a wall is little better than no flashing at all. It is important that flashing penetrating a wythe of brick extend fully to the outside and form a drip. Flashing and counter flashing must be adequately lapped such that water cannot get behind the inner layer to enter the interior of the structure. Furthermore, flashing must be continuous. Any bends or breaks must be completely sealed. Special, preformed shapes that minimize the cutting necessary are available for problem areas such as outside corners.
About: Featured
What Is Biophilic Design?
April 2025

Biophilic design integrates natural elements into built spaces to fulfill our innate connection to nature. Rooted in the biophilia hypothesis, it goes beyond aesthetics, enhancing well-being, health and productivity. 5 Ways to Incorporate Biophilic Desig

One For The Ages - The 75th Midyear
April 2025

“One for the ages” this is how I would describe the upcoming midyear to anyone who has never attended or are undecided about attending MCAAs 75th Anniversary at The Grand Hotel on Mackinac Island September 7-11 2025. In short “one for the ages” means so

A Greener Future Through Masonry
April 2025

When it comes to building a more sustainable future, the construction and building materials sector has a lot of room for growth. According to the most recent data, construction and building-related emissions are responsible for 40% of greenhouse gas emis

MASONRY STRONG Podcast Episode 19 Recap: Mike & Tom Finch
April 2025

On this episode of the MASONRY STRONG Podcast, Mike and Tom Finch join the set in Indianapolis to crack jokes, talk about how they both got started in this industry, and the ways they've seen this trade advance and evolve over the years. The Roots of a F